FL05RD1R0ET [TAIYO YUDEN]
Data Line Filter, 1 Function(s), 0.5A, ROHS COMPLIANT PACKAGE-2;型号: | FL05RD1R0ET |
厂家: | TAIYO YUDEN (U.S.A.), INC |
描述: | Data Line Filter, 1 Function(s), 0.5A, ROHS COMPLIANT PACKAGE-2 LTE |
文件: | 总12页 (文件大小:271K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Notice for TAIYO YUDEN productsꢀ
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called“TAIYO YUDEN’s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and For-
eign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
LEADED NORMAL MODE CHOKE COILS FOR DC AND SIGNAL LINES
WAVE
■ FEATURES
■ APPLICATIONS
◦Use of high loss ferrite materials for excellent high frequency noise
absorption.
◦Absorption of high frequency noise from digital equipment data lines.
■ OPERATING TEMP.
◦High impedance for normal mode applications.
◦05 RD type available in taping for automatic insertion.
◦06 BT type is designed for high current applications (3A).
◦ー25℃~105℃(Including self-generated heat)
■ ORDERING CODE
【FL-R / RD Type】
F L 0 5 R D 2 0 0 A T ○
❶
❷
❸
❹
❺
❻
❼
❶Type
Wound torroids
and beads
❸Shape
❹Nominal inductance
(μH)
example
❺Inductance tolerance
Higher than normal value
❻Packaging
Bulk
❼Internal code
Standard product
Ring core,
A
E
△
T
△
FL
R△
with single wire lead
Special tolerance
Tape & Reel
Ammo
Product classification
code
07
Ring core,
with case, pin type
1R0
200
1.0
20.0
Z
RD
❷Dimensions of core
05
△=Blank space
ー
Special code
△=Blank space
4.8mm
△=Blank space
※R=decimal point
【FL-BT Type】
F L 0 6 B T △ 0 4 ○
❶
❷
❸
❹
❺
❶Type
FL Wound torroids and beads
❷Dimensions of core
❸Shape
Cylinder,
porous core
❹Product classification code
△04
❺Internal code
Standard product
△=Blank space
(diameter)
△
BT
06
6.0mm
△=Blank space
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
Type
〔05RD〕
〔05R〕
〔06BT04〕
9.0max
3.7max
(0.35max)
(0.146max)
6.5max
(0.256max)(0.118max)
3.0max
15.2max
(0.598max)
Fig.
φ0.6
(φ0.024)
φ6.0±0.2
(φ0.24±0.008)
φ0.3
(φ0.012)
+0.6
ー0.2
5.0
+0.024
ー0.008
(0.197
)
Bulk
400
2000
1500
500
ー
ー
250
Minimum
Quantity
(pcs.)
Tape & Reel
Ammo
ー
ー
Unit : mm (inch)
■ IMPEDANCE-FREQUENCY CHARACTERISTICS
Measured by HP4291A
FL05RD / FL05R TYPE
FL06BT TYPE
Please contact TAIYO YUDEN for further information in regard to other characteristics.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ PART NUMBERS
EHS (Environmental
Hazardous
Inductance
[μH]
Impedance
〔Ω〕(typical)
DC Resistance
〔Ω〕(max)
Rated current
〔A〕(max)
Ordering code
Substances
)
+1.0
FL05RD 1R0E□
FL05R 100A
RoHS
1.0
800 (at 400MHz)
900 (at 200MHz)
0.08
0.05
0.5
1.5
3.0
-0.5
RoHS
10 min.
FL05RD 100A□
FL05R 200A-07
FL05RD 200A□
FL06BT 04
RoHS
RoHS
20 min.
2000 (at 100MHz)
1000 (at 150MHz)
0.08
0.05
RoHS
RoHS
ー
□Please specify the packaging code (T: Tape & reel, Z : ammo, Blank space : bulk)
/
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ PACKAGING
①Minimum Quantity
Type
Minimum Quantity (pcs.)
Bulk
500
400
250
Tape & Reel
Ammo
ー
1500
FL05R
ー
2000
ー
FL05RD
FL06BT
ー
②Taping dimensions
◦FL05RD
Type
Symbol
Dimension
D1
H2
T
9.0 max. (0.354 max.)
9.0 max. (0.354 max.)
3.7 max. (0.146 max.)
H1
H
31.0 max. (1.22 max.)
18.0±1.0 (0.709±0.039)
12.7±1.0 (0.500±0.039)
12.7±0.3 (0.500±0.012) ※1
3.85±0.8 (0.152±0.031)
6.35±1.3 (0.250±0.051)
P
P0
P1
P2
W1
+0.75
+0.030
)
ー0.020
9.0
(0.354
ー0.5
FL05RD
+0.6
+0.024
)
ー0.008
F
d
5.0
(0.197
ー0.2
φ0.6 (φ0.024)
△h
W
W0
W2
ℓ
D0
L
0±2.0 (0±0.079)
+1.0
ー0.5
+0.024
18.0
(0.709
)
ー0.008
12.5 min. (0.492 min.)
3.0 min. (0.118 min.) ※2
0 max. (0 max.)
4.0±0.3 (0.157±0.012)
11.0 max. (0.433 max.)
0.7±0.2 (0.028±0.008)
t
※1 Accumulated error for 20 pitches shall be within ±2mm.
※2 Pasting tape shall not exceed paste board.
Unit : mm (inch)
③Reel size
◦FL05RD
60 or les〔s 53〕
(2.362 or les〔s 2.087〕
Unit : mm (inch)
)
Dimensions in parenthesis are measured value.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
1. Operating temperature Range
LA Type
CAL45 Type
ー25~+105℃
LHL□□□
FBA/FBR
ー25~+85℃
ー25~+105℃
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA・CA・FL : Including self-generated heat
LHL□□□ : Including self-generated heat
2. Storage temperature Range
LA Type
CAL45 Type
LHL□□□
FBA/FBR
ー40~+85℃
FL05□ Type
FL06BT Type
3. Rated current
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: The maximum DC value having inductance within 10% and temperature incease within 40℃ (LA:20℃) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10:within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25℃ (LHL08, LHL10, LHL13)
: 30℃ (LHL16, LHLP□□)
: 40℃ (LHLC08, LHLC10)
FB
FL
: No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
: The maximum DC value having temperature rise within specified value.
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
Refer to individual specification
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB
: Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
5. Inductance
LA Type
CAL45 Type
Within the specified tolerance
LHL□□□
FBA/FBR
FL05□ Type
Within the specified tolerance
FL06BT Type
【Test Method and Remarks】
LA, CA
: Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285A+HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
FL05R□ : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A+HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
7. DC Resisitance
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Within the specified tolerance
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB・FL : Measuring equipment : DC ohmmeter
8. Self resonance frequency
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type
△L/L : Within ±5%
CAL45 Type
LHL□□□
△L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Change of maximum inductance deviation in step 1 to 5
Step
Temperature (℃)
1
2
3
4
5
20
ー25 (Minimum operating temperature)
20 (Standard temperature)
+85 (Maximum operating temperature)
20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20℃
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20℃ (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20℃
10. Tensile strength test
LA Type
CAL45 Type
No abnormality such as cut lead, or looseness.
LHL□□□
FBA/FBR
No abnormality such as cut lead, or looseness.
No abnormality such as cut lead, or looseness.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA
: Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
25
duration (s)
5
CA
: Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
10
duration (s)
10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm)
force (N)
duration (s)
0.3<φd≦0.5
5
0.5<φd≦0.8
0.8<φd≦1.2
10
25
30±5
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axial diretion of the component during 10±1 seconds.
FL05R□ : Fix the body of a component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
11. Over current
LA Type
No emission of smoke no firing.
CAL45 Type
There shall be no scorch or short of wire.
LHL□□□
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□/LA・CAL45 Type:Measuring current
Duration
: Rated current×2
: 5 min.
Number of measuring
: one time
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
12. Terminal strength : bending
LA Type
CAL45 Type
No abnormality such as cut lead, or looseness.
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
Bending force
(N)
Mass reference weight
(kg)
φd (mm)
0.3<φd≦0.5
0.5<φd≦0.8
2.5
5
0.25
0.50
LH・FB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
Bending force
(N)
Mass reference weight
(kg)
φd (mm)
0.3<φd≦0.5
0.5<φd≦0.8
0.8<φd≦1.2
2.5
5
0.25
0.5
10
1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□
FBA/FBR
100MΩ min.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Applied voltage : 500 VDC
Duration
: 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR
1MΩ min. (Other than materail code MA)
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FBA・FBR : Applied voltage : 100 VDC
Duration
: 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□
FBA/FBR
No abnormality such as insulation damage
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration
: 60 sec.
16. DC bias characteristic
LA Type
△L/L : Within ー10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type
No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR
No abnormality such as cracks on body.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA
: Applied force : 30N
Duration
Speed
: 10 sec.
: Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration
Speed
: 10 sec.
: Shall attain to specified force in 2 sec.
FBA
: Applied force : 50±3N
Duration : 30±1 sec.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
18. Resisitance to vibration
LA Type
△L/L : Within ±5%ꢀQ : 30min
△L/L : Within ±5%
CAL45 Type
LHL□□□
Appearance : No abnomality
△L/L : Within ±5%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Appearance : No abnomality
Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB:Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type
No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
:
Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type
At least 75% of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□
FBA/FBR
At least 75% of terminal electrode is covered by new solder.
At least 90% of terminal electrode is covered by new solder.
FL05□ Type
FL06BT Type
At least 75% of terminal electrode is covered by new solder.
【Test Method and Remarks】
LA, CA
: Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5℃
Duration
Immersion depth
: 2±0.5 sec.
: Up to 1.5mm from bottom of case.
FB
: Solder temperature : 230±5℃
Duration
: 3±1 sec.
Immersion depth
: Up to 1.5mm from terminal root.
FL05R□ : Solder temperature : 230±5℃
Duration
Immersion depth
: 2±0.5 sec.
: Up to 2 to 2.5mm from terminal root.
FL06BT
: Solder temperature : 230±5℃
Duration
: 3±1 sec.
Immersion depth
: Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type
No significant abnormality in appearance
△L/L : Within ±5%
CAL45 Type
LHL□□□
FBA/FBR
No significant abnormality in appearance
No significant abnormality in appearance
Refer to individual specification
Inductance change : Within ±5%
Impedance change : Within ±20%
Q change : Within ±30%(LHLP : only △L/L)
FL05□ Type
FL06BT Type
No significant abnormality in appearance
Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA
: Solder temperature : (CA) 270±5℃, (LA) 260±5℃
Duration
: 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5℃
Duration
: 10±1 sec.
Up to 1.5mm from the bottom of case.
Manual soldering
: Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration
: 5±1 sec.
Up to 1.5mm from the bottom of case.
Caution
: No excessive pressing shall be applied to terminals.
Recovery
: 4 to 24hrs of recovery under the standard condition after the test.
FB
FL
: Solder bath method : Condition 1 : Solder temperature : 260±5℃
Duration
: 10±1 sec.
Immersion depth
: Up to 1.5mm from the terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration
Immersion depth
: 3±1 sec.
: Up to 1.5mm from the terminal root.
Recovery
: 3hrs of recovery under the standard condition after the test.
: Solder condition
Immersion depth
Recovery
: 260±5℃
10±1 sec.
: Up to 0.5 to 1.0mm from the terminal root.
: 3hrs of recovery under the standard condition after the test.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
22. Resisitance to solvent
LA Type
Please avoid the ultrasonic cleaning of this product.
No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB : Solvent temperature : 20~25℃
Duration
Solvent type
Recovery
: 30±5 sec.
: Acetone
: 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Appearance : No abnormality
Refer to individual specification
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP:only △L/L)
FL05□ Type
FL06BT Type
Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA
: Conditions for 1cycle
Step
Temperature (℃)
Duration (min.)
30±3
Within 3
30±3
+0
ー3
1
2
3
4
ー25
Room temperature
+2
+85
ー0
Room temperature
Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□□・FB : Accoding to JIS C0025
Conditions for 1 cycle
Step
Temperature (℃)
Minimum operating temperature
Room temperature
Duration (min.)
30±3
Within 3
30±3
+0
ー3
1
2
3
4
+2
ー0
Minimum operating temperature
Room temperature
Within 3
Number of cycles : 10 cycles〔LHL□□□〕
: 5 cycles (FBA, FBR)
Recovery
: 4 to 24hrs of recovery under the standard condition after the removal from the test chamber.〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL
: Accoding to JIS C0025
Conditions for 1 cycle
Step
Temperature (℃)
Duration (min.)
30±3
Within 3
30±3
+0
ー3
1
2
3
4
ー25
Room temperature
+2
+85
ー0
Room temperature
Within 3
Number of cycles : 10 cycles
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance:No abnormality
Impedance change:Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity
Duration
Recovery
: 90~95%RH
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2℃
Humidity
Duration
Recovery
: 90~95%RH
: 1000 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ RELIABILITY DATA
25. Loading under damp heat
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Imductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LA, CA
: Temperature
Humidity
: 40±2℃
: 90~95%RH
Duration
: 1000 hrs
Applied current : Rated current
Recovery
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature
Humidity
: 40±2℃
: 90~95%RH
: 1000±24 hrs
Duration
Applied current : Rated current
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature
Humidity
Duration
: 60±3℃
: 90~95%RH
: 500 (+12, ー0) hrs
Applied current : Rated current
Recovery
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA
: Temperature
Duration
: 85±2℃
: 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type
△L/L : Within ±10%ꢀQ : 30min
△L/L : Within ±10%
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LA, CA
: Temperature : ー25±2℃
Duration
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
Recovery
LHL□□□ : Temperature : ー40±3℃
Duration
Recovery
: 1000±24 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature : ー40±3℃
Duration
: 500 (+12, ー0) hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
Recovery
28. High temperature life test
LA Type
CAL45 Type
LHL□□□
FBA/FBR
Appearance : No abnormality
Inductance change : Within ±10%
Impedance change : Within ±20%
Q change : Within ±30% (LHLP : only △L/L)
FL05□ Type
FL06BT Type
Refer to individual specification
Appearance : No abnormality
【Test Method and Remarks】
LHL□□□ : Temperature : 105±3℃
Duration
Recovery
: 1000±24 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL
: Temperature : 85±3℃
Duration
: 500 (+12, ー0) hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
Recovery
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
■ PRECAUTIONS
CAL Type, LH Type, FB Type, FL Type, LA Type
1. Circuit Design
◆Operating environment
1.The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
Precautions
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
◆Design
Precautions
1.Please design insertion pitches as matching to that of leads of the component on PCBs.
Technical ◆Design
consider-
ations
1.When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
◆Adjustment of mounting machine
1.Excessive impact load should not be imposed on the products when mounting onto the PC boards.
Precautions
2.Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1.When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Precautions
Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical ◆Lead free soldering
consider-
ations
1.If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical ◆Cleaning conditions
consider-
ations
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
Precautions
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
Technical
consider-
ations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
◆Storage
1.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
Precautions
・Ambient temperature 0~40℃
・Humidity
Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical ◆Storage
consider-
ations
1.Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
*This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Taiyo Yuden:
FL05RD100AT FL05RD100AZ FL05RD1R0E FL05RD1R0ET FL05RD1R0EZ FL05RD200A FL05RD200AT
FL06BT04
相关型号:
©2020 ICPDF网 联系我们和版权申明